Jensen MP3 Docking Station JiSS 330 User Manual

DOCKING SPEAKER STATION FOR iPod®  
OWNER'S MANUAL  
JiSS-330  
(iPod® Not Included)  
PLEASE READ THIS OPERATING MANUAL COMPLETELY BEFORE OPERATING  
THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE  
JISS-330 US IB V.02  
: 148.5 X 210mm  
8 210 x 297mm 32  
80gms bk+bk  
2007.05.30  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Expand Contents

DEAR JENSEN CUSTOMER  
IMPORTANT SAFETY INSTRUCTIONS  
Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical  
enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers.  
This manufacturer and the Electronic Industries Association's Consumer Electronics Group want you to get  
the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and  
clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing.  
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of sound. So what  
sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your  
equipment at a safe level BEFORE your hearing adapts.  
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety.  
However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating  
instructions carefully before installation and use, and keep these instructions handy for future reference. Take  
special note of all warnings listed in these instructions and on the unit.  
1.Water and Moisture  
The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink, laundry tub,  
swimming pool or in a set basement.  
2.Ventilation  
The unit should be situated so that its location or position does not interfere with its proper ventilation.  
To establish a safe level:  
Start your volume control at a low setting.  
For example, it should not be situated on a bed, sofa, rug or similar surface that may block the ventilation openings.  
Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.  
Once you have established a comfortable sound level:  
Set the dial and leave it there.  
Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow  
of air through the ventilation openings.  
Minimum distances (10cm) around the apparatus for sufficient ventilation; the ventilation should not be impeded  
by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc.  
3.Heat and Flame  
The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances  
(including amplifiers) that produce heat.  
No naked flame sources such as lighted candles should be placed on the apparatus.  
4.Power Source  
The unit should be connected to a power supply only of the type described in the operating instructions or as  
marked on the appliance.  
5.Cleaning  
Taking a minute to do this now will help to prevent hearing damage or loss in the future.After all, we want  
you listening for a lifetime.  
We Want You Listening For a Lifetime  
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage  
from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries  
Association's Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise.  
Customer's Record:  
The serial number of this product is found on its bottom cover. You should note the serial number of this unit  
in the space provided as a permanent record of your purchase to aid in identification in the event of theft of  
loss.  
The unit should be cleaned only as recommended. See the section "Care and Maintenance" of this manual for  
cleaning instructions.  
6.Object and Liquid Entry  
Care should be taken so that objects do not fall and liquids are not spilled into any openings or vents located on  
the product.  
7.Attachments  
Do not use attachments no recommended by the product manufacturer.  
8.Lightning and Power Surge Protection  
Model Number: JiSS-330  
Serial Number:  
Unplug the unit from the wall outlet and disconnect the periods of time. This will prevent damage to the product due  
to lightning and power-line surges.  
9.Overloading  
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire  
of electric shock.  
10.Damage Requiring Service  
This unit should be serviced by qualified service personnel when:  
A.The power supply cord or plug has been damaged.  
B.Objects have fallen into or liquid has been spilled into the enclosure.  
C.The unit has been exposed to rain.  
D.The unit has been dropped or the enclosure damaged.  
E.The unit exhibits a marked change in performance or does not operate normally.  
11.Periods of Nonuse  
If the unit is to be left unused for an extended period of time, such as a month or longer, the AC adaptor should be  
unplugged from the unit to prevent damage or corrosion.  
12.Environment  
Attention should be drawn to the environmental aspects of battery disposal; the use of apparatus in moderate  
climates.  
13.Servicing  
The user should not attempt to service the unit beyond those methods described in the user's operating  
instructions. Service methods not covered in the operating instructions should be referred to qualified service  
personnel.  
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPLIANCE WITH FCC REGULATIONS  
INSTALLATION  
Remote Control battery  
The battery compartmentis located on the bottom ofthe Remote Control.  
(1) Remove the battery compartment door.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
(2) Follow the polarity diagram shown inside the compartment and install 2 x "AAA" batteries  
(included).  
(3) Replace the battery compartment door.  
In accordance with FCC requirements, changes or modifications to this unit not expressly approved by the  
party responsible for compliance could void the user's authority to operate the equipment.  
NOTE:  
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant  
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates, uses and can radiate radio frequency  
energy and, if not installed and used in accordance with the instructions, may cause harmful interference  
to radio communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception, which can be  
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by  
one or more of the following measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
- Consult the dealer or an experienced radio/TV technician for assistance.  
WARNING:  
- Be sure that the batteries are installed correctly. Wrong polarity may damage the Remote Control.  
- Do not mix old and new batteries.  
- Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.  
- Only batteries of the same or equivalent type as recommend are to be used.  
- If theRemote Control is not to be used for an extended period of time, remove the battery.  
- Do not dispose of batteries in fire, batteries may explode or leak.  
AC Adaptor Connection  
The unit is powered by an external AC Adaptor with an output of 15V DC , 1100 mA (included).  
(1) Firmly and securely plug the AC Adaptor into AC main outlet.  
(2) Insert theAC Adaptor output plug to the power input jack on the back ofthe unit.  
LOCATION OF CONTROLS  
Main Unit  
PRODUCT FEATURES  
Top view  
Front view  
4
1
2
3
5
JiSS-330 is aDocking Speaker Stationfor iPod whichincorporates the followingfeatures :  
Player / Re-chargerfor iPod , iPodmini and iPod nano  
Interchangeable iPodAdaptors  
Video Line-out provides video signaloutput when iPod with video isdocked  
Audio line-infor connecting otherdigital audio player  
Built-in 3 HighFidelity Speakers withsurround sound effect.  
Subwoofer output signalis available forthe connection ofan external active(self-powered)  
subwoofer.  
Rear view  
6
7
8
9
10 11 12  
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
LOCATION OF CONTROLS  
iPod ADAPTORS  
1. iPod® docking bay  
Please see below for the iPod Adaptor included in the package:  
2. iPod® docking connector  
iPod Models  
iPod Adaptor  
3. ON/STANDBY  
button ----- To turn the uniton or off.  
4. VOLUME +/ - button ----- Adjust volume levelup or down.  
5. Three Speakers  
6. Remote InfraredSensor  
Docking Cover  
7. DC15V INjack ----- Forthe connection ofexternal DC powersupply.  
8. S-VIDEO Jack ----- S-Video signal output  
9. RCA VIDEO Jack ----- Compositevideo signal output  
10. Subwoofer Out----- For theconnection of externalactive(self-powered) Subwoofer.  
11. AUXInput Jack ----- Forthe connection of external audio inputsource.  
12. Audio Input Selector switch ----- Select iPOD orAuxiliary input.  
Align  
1st G en  
iP od nano  
here  
Align  
2nd G en  
iP od nano  
here  
iPod nano  
iPod mini  
Remote Control  
1
3Gen iPod 10/15GB  
4Gen iPod 20GB  
iPod Photo 20/30GB  
2
3
3Gen iPod 30/40GB  
4Gen iPod 40GB  
4
6
5
iPod Photo 40/60GB  
NOTE : No adaptors are provided for iP od with video 30G B, 60G B and 80G B. P lease use the adaptors  
included with these iP ods at time of purchase. They will fit properly into the docking bay of  
this system.  
1. Infra-red Transmitter  
2. ON/STANDBY  
3. iPod PLAY / PAUSE  
4. buttons ----- SkipiPod tracks Forward/Backwardor perform high-speedsearch.  
button ----- To turn the uniton or off  
button  
/
5. VOLUME +/ - button ----- Adjust volume levelup or down.  
6. Battery Compartment-----located on bottomof the RemoteControl.  
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
SYSTEM PLACEMENT  
iP od DOC K ING  
We recommend that you placethe JiSS-330 properlyon your desk, counter or table.  
The unit producesexceptional sound fromany listening positionin the room.  
However, thebest quality soundand surround soundeffects will be heard withthe unit  
placed directly infront of youand facing you.  
This model includes adaptors for adopting different iP od models. If the docking bay will not be used for  
an extended period of time, it is recommended to use the "Dock C over" insert to help protect the docking  
connector.  
1. S elect a suitable adaptor for your iP od and insert it into the docking bay .  
2. Your iP od can now be docked by placing the connector on the bottom of  
the iP od directly over the dock connector located in the docking bay.  
S eat the iP od on the dock connector to assure a proper connection.  
For docking an iP od nano, slide the dock connector to the left and also  
see note on " DOC KING 1st AND 2nd G E NE R ATION iP od nanos "  
section of this instruction manual.  
Not Preferred  
Preferred  
PC  
PC  
For other iP od models, slide the dock connector to the right (center position)  
and insert the iP od adaptor for the type of iP od you are using.  
3. Insert your iP od with the connector facing down and positioned directly over the dock connector located  
in the docking bay. S eat the iP od on the dock connector to assure a proper connection.  
1-6ft  
USER  
USER  
Not Preferred  
PC  
Preferred  
Ins ert the iP od  
a da ptor into the  
docking bay  
Dock your iP od  
with the connector  
in the docking ba y  
PC  
Note: When docking your iP od, please be careful to avoid damaging the 30-pin connectors located on  
the iP od and in the docking bay.  
1-6ft  
4. S lide the Audio Input S elector switch on the back of the unit to iP od position.  
5. P ress the ON/S TANDB Y  
6. P ress the P L AY / PAUS E  
button to turn On the main unit.  
USER  
button from the R emote C ontrol to pause or resume iP od playback.  
USER  
7. Adjust the sound level by pressing the VOL UME + / - buttons.  
Note : The Volume level cannot be adjus ted us ing the volume control on your iP od when  
docked.  
Refer to youriPod operation manualto adjust the"EQ" setting onyour iPod. This will enhancethe  
sound and alsohelp adjust thesound to theroom you areusing it in.  
8. The iP od charges even during playback.  
9. To remove the iP od from the Docking bay, press and hold the P L AY/PAUS E button for three seconds  
to switch off the iP od. You can now gently remove it from the docking bay.  
iP od playback control from remote control:  
- P ress the P L AY/PAUS E  
- P ress the iP od S kip/S earch Forward  
- P ress and hold the iP od S kip/S earch Forward  
fast-rewinding during playback.  
button to pause or resume the iP od playback;  
or Backward button to skip to the next or previous song;  
or Backward button for fast-forwarding or  
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
DO C K ING 1s t A ND 2nd G E NE R A T IO N iP od na nos  
AUXILIARY INPUT  
F irs t ins tall the iP od nano bracketinto the J iS S -330 B ay.  
This model providesan auxiliary audiosignal input forconnecting an externalaudio device.  
You may connect anaudio cable with3.5 mm stereoplug (included) tothe AUX IN Jack located on  
the back ofthe unit. Connectthe other endof the cableto the LineOut Jack orHeadphone Jack of  
your MP3 player, CD playerand other non-dockableiPods.  
1s t G eneration iP od nano: Align your 1s t generation iP od nano to the  
L E F T s ide of the opening in the nano bracket(F igure 1 ). Make s ure  
the connector on the bottom of the nano is pos itioned over the  
connector in the J iS S -330 dock prior to s eating the nano. C arefully  
s lide the nano down onto the connector in order to ins ure a s ecure  
connection.  
You can now listento your externalsource through thespeakers of thissystem.  
1. Connect anaudio cable with3.5 mm stereoplug to theAUX IN Jack located onthe back ofthe  
unit.  
Figure 1  
2nd G enera tion iP od na no: Align your 2nd genera tion iP od na no to the  
R IG HT s ide of the opening in the na no bra cket(F igure 2 ). Ma ke s ure  
the connector on the bottom of the na no is pos itioned over the  
connector in the J iS S -330 dock prior to s ea ting the na no. C a refully  
s lide the na no down onto the connector in order to ins ure a s ecure  
connection.  
3.5mm  
Stereo plug  
External Audio Device  
2. Slide theAudio Input Selectorswitch to AUX IN position.  
3. Connect theother end ofthe cable tothe Line OutJack or HeadphoneJack of yourexternal  
audio device.  
Note: B e ca reful not to da ma ge the connector when docking the na no.  
Figure 2  
Never us e force when docking the na no onto the connector.  
4. Turnon the externalaudio device.  
5. The volume level cannow be controlledusing the main unit.  
Operate all otherfunctions on theattached auxiliary deviceas your normallywould.  
VIDEO OUT FROM THE iPod  
Note:  
(1) If your connectedusing the LineOut Jack ofyour external device, then you canonly adjust the  
volume using theJiSS-330 control. Ifyour connected usingthe Headphone Jackof your  
external device, thenyou may needto adjust boththe volume controls(JiSS-330 and external  
device) to getthe best volumelevel.  
(2) Press the ON/STANDBY button to turnoff the unit when youfinish listening.  
Don't forget toswitch off the power ofyour external deviceas well.  
You are able to view videos and photos stored in your 5th Generation iPod on a larger television screen  
or monitor using the built-in Video Output jacks on the back of the unit.  
Two video output jacks are available on the back of the unit.  
(1) S-VIDEO  
(2) RCA VIDEO  
S-Video signal.  
composite video signal (most common on standard televisions with video in).  
Video Out (For 5th Generation iPods with video ONLY)  
1. You can connect this unit to a television or other video display that has S-video or composite  
video inputs.  
2. Securely dock the iPod with video in the docking bay.  
3. Connect the S-video cable (included) into the rear S-video jack or yellow RCA cable (included) to rear  
RCA video jack on the unit.  
4. Connect the other end of the S-video or yellow RCA cable to VIDEO IN on your television or video display.  
5. Slide the Audio Input Selector switch on the back of the unit to iPod position.  
6. Select a movie from your iPod menu.  
7. iPod: On the main menu choose video then select video setting.  
8. iPod: Make sure the TV Out section is set to ON.  
9. iPod: Switch back to the movie library and play the movie of your choice.  
For Photo view (For iPod with color display ONLY - excludes nano)  
1. Slide the Audio Input Selection switch on the back of the unit to iPod position.  
2. Securely dock the iPod with color display.  
3. iPod: At TV Out section, make sure it is set to ON”  
4. iPod: Go to Photo Library and then press play. The slideshow will play on your device.  
Note: 1. The RCA Video input connector on a television is usually color coded yellow to match the  
color on the AV cable.  
2. When playing slideshows or videos, the audio will only playback through the speakers on this unit.  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUBWOOFER OUTPUT  
TROUBLESHOOTING GUIDE  
This unit provides a seperate subwoofer output jack for connecting an external active  
(self-powered) subwoofer speaker (not included). This will enhance and expand your sound by  
adding an extra deep rich bass channel to the unit. The Subwoofer Output Jack is located on the  
back of the unit.  
Symptom  
Possible Problem  
Solution  
AC Adaptor is not plugged into a  
wall outlet or the output connector  
is not plugged into the DC15V IN  
jack on the back of the unit.  
Plug the AC adaptor into a wall  
outlet and plug the output connector  
into the DC15V IN jack on the unit.  
The unit does  
not respond (no power)  
Plug another device into the same  
outlet to confirm the outlet is working.  
Wall outlet is not functioning.  
Using no/wrong iPod Adaptor.  
iPod does not install properly.  
Make sure the dock insert is the  
proper fit for your iPod.  
iPod does not  
dock properly  
Remove your iPod from the dock  
and check for obstruction on the  
connectors in the dock and on your  
iPod. Then reseat it in the dock.  
iPod is not installed properly.  
Your iPod is locked up.  
Remove your iPod from the dock  
and check for obstruction on the  
connectors in the dock and on your  
iPod. Then reseat it on the dock.  
iPod does not respond  
to the speaker system  
Please make sure that your iPod is  
working properly before docking into  
the unit. Please refer to your iPod  
manual for info on resetting the iPod.  
CARE AND MAINTENANCE  
- Do not subject the unit to excessive force, shock, dust or extreme temperature.  
- Do not tamper the internal components of the unit.  
iPod mode is not selected.  
iPod is not installed properly.  
Slide the Audio Input Selection  
switch at the back of the unit to  
iPod position.  
- Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.  
- Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.  
- Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps  
or motors.  
Remove your iPod from the dock  
and check for obstruction on the  
connectors in the dock and on your  
iPod. Then reseat it in the dock.  
iPod does not  
charge up  
iPod is locked up/ frozen.  
iPod battery has problem.  
Please make sure your iPod is  
working properly before docking into  
the unit. Please refer to your iPod  
manual for details on resetting.  
Volume level is set too high.  
Decrease the volume.  
If the iPod original sound source is of  
poor quality, distortion and noise are  
easily noticed with high-power  
speakers. Try a different audio source  
such as a music CD.  
Sound is distorted  
Sound source is distorted.  
If you are using an external sound  
source like older generation of iPod,  
try reducing the output volume on the  
device itself. Also try turning bass  
boost OFF or change the EQ setting.  
Unit gets warm after  
extended play at  
high volume  
This is normal.  
Turn the unit off for a period of time or  
lower volume.  
12  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
Power Requirement  
Main unit  
DC input :  
DC 15V, 1100 mA  
Remote Control  
2 x DC1.5V "AAA" (UM-4) Batteries  
100 - 16000Hz  
Frequency Response  
Total Power Output  
10Wmax  
SERVICE  
Please refer to the instructions on the enclosed warranty card for returning your unit for service. When  
returning the unit, please remove batteries to prevent damage to the unit in transit and/or from possible  
leakage. We are not responsible for batteries returned with the product or for the cost of replacement.  
Distributed by:  
SPECTRA Merchandising International, Inc.  
Chicago Industry Tech Park  
4230 North Normandy Avenue  
Chicago, IL 60634, U.S.A.  
Please have model number ready, for Customer Service, call 1-800-777-5331.  
*The specification and external appearance of the set are subject to change without prior notice.*  
Printed in China  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Jensen Car Stereo System HD5212 User Manual
Jensen Car Stereo System JCD3006 User Manual
Jensen Flat Panel Television JE2608 User Manual
Jensen MP3 Docking Station JiSS 250i User Manual
Jensen Saw MGH300