Jensen Car Stereo System CD6111 User Manual

CD6111  
I
n
s
t
r
u
c
t
i
o
n
M
a
n
u
a
l
M
a
n
u
a
l
d
e
I
n
s
t
r
u
c
c
i
o
n
e
s
G
u
i
d
e
d
'
i
n
s
t
r
u
c
t
i
o
n
s
C
D
6
1
1
1
1
6
0
W
A
T
T
S
T
U
N
E
A
U
D
I
O
I
N
P
U
T
R
E
A
D
Y
/
Download from Www.Somanuals.com. All Manuals Search And Download.  

Expand Contents

CD6111  
TABLE OF CONTENTS  
TABLE DES MATIÈRES  
Introduction ..............................................................................................1  
Preparation ..............................................................................................1  
Wiring .......................................................................................................2  
Installation ................................................................................................3  
Operation .................................................................................................4  
Tuner Operation .......................................................................................7  
CD Player Operation ................................................................................8  
CD Changer Operation ............................................................................9  
JPORT Operation ....................................................................................9  
Remote Control ......................................................................................10  
Care and Maintenance ...........................................................................10  
Troubleshooting .....................................................................................11  
Specifications .........................................................................................11  
12-Month Limited Warranty ....................................................................12  
Introduction ............................................................................................25  
Préparation ............................................................................................25  
Câblage .................................................................................................26  
Installation ..............................................................................................27  
Operation ...............................................................................................28  
Opération de la Radio ............................................................................31  
Opération de la Platine CD ....................................................................32  
Opération de Changeur de CD ..............................................................33  
Opération JPORT ..................................................................................33  
Prêt à être Télécommandé ....................................................................34  
Soin et Entretien ....................................................................................34  
Dépannage ............................................................................................35  
Caractéristiques .....................................................................................35  
Garantie Limitée de 12 Mois ..................................................................36  
CONTENIDO  
Introducción ...........................................................................................13  
Preparación ............................................................................................13  
Cableado ................................................................................................14  
Instalación ..............................................................................................15  
Operación ..............................................................................................16  
Operación del Radio ..............................................................................19  
Operación del Equipo de CD .................................................................20  
Operación del Cambiador de CD ...........................................................21  
Operación del JPORT ............................................................................21  
Control Remoto ......................................................................................22  
Cuidado y Mantenimiento ......................................................................22  
Corrección de Problemas ......................................................................23  
Especificaciones ....................................................................................23  
Garantia Limitade de 12 Meses .............................................................24  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD6111  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD6111  
INTRODUCTION  
PREPARATION  
Congratulations on your purchase of the Jensen CD6111 Mobile AM/FM/CD Receiver. It’s a  
good idea to read all of the instructions before beginning the installation. We recommend  
having your Jensen CD6111 installed by a reputable installation shop.  
Tools and Supplies  
The following tools and supplies are needed to install the radio.  
Torx type, flathead and Philips screwdrivers  
Wire cutters and strippers  
Tools to remove existing radio (screwdriver, socket wrench set or other tools)  
Electrical tape  
Crimping tool  
Volt meter/test light  
Crimp connections  
18 gauge wire for power connections  
16-18 gauge speaker wire  
Features  
CD  
CD-R/RW compatible  
Last position memory  
Random/repeat/intro  
High-speed audible track search  
1-Bit D/A converter  
Anti-shock mechanism  
AM/FM TUNER  
24 station presets (12 FM, 6 AM)  
JENSEN Plus Tuner II  
Auto station store/preset scan  
One-touch memory  
Manual stereo/mono, local/distance, and up/down tuning  
Auto seek tuning up/down and 5-second scan tuning  
SPEAKER REQUIREMENTS: Only connect speakers rated in the load impedance of 4  
ohms. Speakers with a load impedance less than 4 ohms could damage the unit.  
Pre-installation  
1. Disconnect Battery  
Before you begin, always disconnect the battery negative terminal.  
2. Remove Transport Screws  
3. Remove Radio from Sleeve  
Chassis  
Electronic detachable face with hard case  
Import ISO/DIN mountable  
20-pin power harness  
Lift latches on both sides of sleeve to remove half-sleeve from radio.  
General  
High contrast Liquid Crystal Display (LCD)  
Infrared remote control (included)  
iEQ3 - instant EQ with 3 selectable EQ curves - Classic, Pop and Rock  
1 pair each rear RCA auxiliary inputs and pre-amp outputs  
Rotary encoder audio control with electronic volume, bass, treble, balance, fader  
Multi-button power on  
Keyless CD eject  
4V Peak / 2V RMS RCA pre-amp output voltages  
Rear RCA pre-amp outputs  
200-ohm low impedance preamp output  
Flex-Fader  
True Blue LED preset illumination  
Loudness  
TRANSPORT  
SCREWS  
HALF  
SLEEVE  
Clock  
Mute  
Theft deterrent LED  
Optional Accessories  
jPORT (Sold Separately)  
Controls your iPod and CD Changer  
jLink Apple approved iPod cable (included)  
jLink Adapter (included)  
iAux (Sold Separately)  
Converts 3.5mm Input to RCA outputs for auxiliary devices  
Under-dash adapter allows for quick installation of portable media devices  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD6111  
WIRING  
WIRING DIAGRAM  
Wiring with a Wiring Adapter (Purchased Separately)  
Connect Wires  
You can make these connections without being in the vehicle.  
1. Splice or crimp wires.  
2. Attach wiring adapter to car wiring harness.  
Wiring Diagram / Color Codes  
1. Power Antenna (dark blue wire) - Connect to power antenna or amplifier. If not used, tape  
bare end of wire.  
2. Accessory/Ignition (red wire) - Connect to existing radio wire or radio fuse.  
3. Ground (black wire) - Connect to ground terminal or clean, unpainted part of chassis.  
4. Memory/Battery (yellow wire) - Connect to battery or 12 volt power source that is always  
live. The radio will not work if this wire is not connected.  
5. Antenna Connector - Connect the antenna plug from the existing antenna cable (some  
vehicles require an adaptor).  
6. CD Changer/JPORT connector - Use this 8-pin DIN socket to connect an optional CD  
Changer or JPORT (sold separately).  
7. Auxiliary Input Cable (yellow RCA cables) - Connect line in for auxiliary input devices (CD  
player, etc.).  
8. Outputs to Amplifier (gray RCA cables) - Connect line out for optional external amplifiers.  
The red connector is for the right and the white connector is for the left.  
9. Left Front Speaker  
10. Right Front Speaker  
11. Left Rear Speaker  
12. Right Rear Speaker  
NOTE: The amplifiers in this radio are only designed for use with four speakers. Never  
combine (bridge) outputs for use with two speakers. Never ground negative speaker  
leads to chassis ground. Failure to wire exactly as shown may cause electrical damage  
to the radio.  
Fuses  
When replacing a fuse, make sure the new fuse is the correct type and amperage. Using an  
incorrect fuse could damage the radio. The CD6111 uses one 15 amp fuse located below the  
wiring connector (15 amp fast blow ATO).  
Reconnect Battery  
When wiring is complete, reconnect the battery negative terminal.  
Optional JPORT  
(Sold Separately)  
Technical Assistance  
If you require assistance, contact Technical Support at 1-800-323-4815 from 8:30am to 7:00pm  
EST Monday through Friday and from 9:00am to 5:00pm EST on Saturday.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD6111  
5. Place the radio in front of the dashboard opening so the wiring can be brought through the  
mounting sleeve.  
INSTALLATION  
This unit is designed for installation in cars, trucks and vans with an existing radio opening. In  
many cases, a special installation kit will be required to mount the radio to the dashboard.  
These kits are available at electronics supply stores and car stereo specialty shops. Always  
check the kit application before purchasing to make sure the kit works with your vehicle. If you  
have trouble locating a kit or need installation assistance, contact Technical Support at 1-800-  
323-4815 from 8:30am to 7:00pm EST Monday through Friday and from 9:00am to 5:00pm  
EST on Saturday.  
Universal Installation Using Mounting Sleeve  
1. Remove the detachable front panel, if it is attached to the chassis, by pushing the  
“Release” button.  
2. Slide the mounting sleeve off of the chassis if it has not already been removed. If it is  
locked into position, use the removal keys (supplied) to disengage it. The removal keys  
are depicted on page 4.  
3. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is  
not large enough, carefully cut or file as necessary until the sleeve easily slides into the  
opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that  
there will be sufficient space behind the dashboard for the radio chassis.  
4. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.  
With the sleeve fully inserted into the dashboard opening, bend as many of the tabs  
outward as necessary to firmly secure the sleeve to the dashboard.  
6. Follow the wiring diagram carefully and make certain all connections are secure and  
insulated with crimp connectors or electrical tape to ensure proper operation.  
7. After completing the wiring connections, attach the front panel and turn the unit on to  
confirm operation (vehicle ignition switch must be on). If the unit does not operate,  
recheck all wiring until the problem is corrected. Once proper operation is achieved, turn  
the ignition switch off and proceed with final mounting of the chassis.  
8. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is  
fully seated and the spring clips lock it into place.  
9. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of  
the chassis using the hex nut provided. Fasten the other end of the perforated strap to a  
secure part of the dashboard either above or below the radio using the screw and hex nut  
provided. Bend the strap, as necessary, to position it. CAUTION: The rear of the radio  
must be supported with the strap to prevent damage to the dashboard from the weight of  
the radio or improper operation due to vibration.  
10. Re-attach the front panel to the chassis and test radio operation by referring to the  
operating instructions for the unit.  
NOTE: For proper operation of the CD player, the chassis must be mounted within 20° of  
horizontal. Make sure the unit is mounted within this limitation.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD6111  
Kit Installation  
If your vehicle requires the use of an installation kit to mount this radio, follow the instructions  
included with the installation kit to attach the radio to the mounting plate supplied with the kit.  
OPERATION  
Power  
Press the power button (1) or any other button on the face of the receiver to turn the unit on  
when the ignition switch is on. Press the power button again to turn the receiver off. If the radio  
was left on when the ignition was last turned off, the receiver will turn on automatically when  
the ignition switch is again turned on. If the receiver was off when the ignition was last turned  
off, the receiver must be turned on manually when restarting the vehicle.  
1. Wire and test the radio as outlined in the Universal Installation instructions.  
2. Install the radio/mounting plate assembly to the sub-dashboard according to the  
instructions in the installation kit.  
3. Attach the support strap to the radio and dashboard as described in the Universal  
Installation instructions.  
4. Replace the dashboard trim panel.  
Mode  
Press MODE (2) to select a different mode of operation as indicated on the display panel.  
Available modes include Tuner, CD, CD changer (CDC) and Auxiliary Input. During CD player  
operation, pressing MODE will change to the tuner mode without ejecting the disc. The CD  
icon (7) will remain in the display to indicate that a disc is still loaded in the unit. Unless a CD  
changer is connected to the unit, the CD changer (CDC) mode cannot be accessed. To access  
the Auxiliary Input mode, press the MODE button until "AUX" is indicated in the display.  
ISO Installation  
This unit has threaded holes in the chassis side  
panels which may be used with the original factory  
mounting brackets of some vehicles to mount the  
radio to the dashboard. Please consult with your  
local car stereo shop for assistance on this type of  
installation.  
Volume  
1. Remove the existing factory radio from the  
To increase the volume, rotate the volume control (3) clockwise. To decrease the volume,  
rotate the volume control counter clockwise. When volume is adjusted, the volume level is  
shown on the display panel as a number ranging from “00” (lowest) to “100” (highest).  
dashboard or center console mounting. Save all  
hardware and brackets as they will be used to  
mount the new radio.  
Select  
2. Carefully unsnap the plastic frame from the  
front of the new radio chassis. Remove and discard the frame.  
3. Remove the factory mounting brackets and hardware from the existing radio and attach  
them to the new radio. Do not exceed M5 x 9 MM maximum screw size. Longer screws  
may damage components inside the chassis.  
Press PUSH (4) to step through the menu of audio functions. The first option is volume (VOL),  
followed by bass (BAS), treble (TRB), balance (BAL), fader (FAD), and again by volume (VOL).  
When adjusting audio functions, the unit will automatically exit select mode and return to the  
normal display after five seconds or when another function is activated.  
4. Wire the new radio to the vehicle as outlined in the Universal Installation instructions.  
5. Mount the new radio assembly to the dashboard or center console using the reverse  
procedure of step 1.  
Remove Radio  
To remove the radio after installation, remove the  
trim ring by lifting in the center and pulling it off  
from either side. Insert the removal keys straight  
back until they lock, and then pull the radio out. If  
removal keys are inserted at an angle, they will not  
lock properly to release the unit.  
REMOVAL KEYS  
Select (continued)  
Bass  
Press PUSH (4) twice until “BAS” appears in the display. Within five seconds, rotate the  
volume control (3) clockwise or counter clockwise to adjust the bass from “-10” to “+10”. “00”  
represents a flat response. The bass level is shown on the display for five seconds or until  
another function is activated.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.