MP6212
Instruction Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
MP6212
INTRODUCTION
Congratulations on your purchase of the Jensen MP6212 Mobile Receiver.
It’s a good idea to read all of the instructions before beginning the
installation. We recommend having your Jensen MP6212 installed by a
reputable installation shop.
•
•
•
Rear Line Output
200-Ohm Preamp Line Outputs
2VRMS Line Outputs
Features
CD / MP3 / WMA
•
•
•
•
•
•
•
•
ID3 Tag Compatible
Last Position Memory
Directory Search (MP3 / WMA Only)
MP3/WMA search by Track, File and Character
Audible Forward / Reverse Track Search
Random, Repeat and Intro
Play, Pause, Stop, Next Track and Previous Track
ESP Buffer (Electronic Shock Protection)
AM-FM
•
•
•
•
•
•
RDS - Radio Data Service
USA / Europe Frequency Spacing
30 Station Presets (18 FM / 12 AM)
Auto Stereo / Mono
Local / Distance
Auto Store / Preview Scan
Sat Radio Ready
•
•
Compatible with XM and Sirius Tuners (Sold Separately)
Requires XMDJEN100 and JXMC Cables (Sold Separately)
Chassis
•
•
•
•
Detachable Faceplate
1.0 DIN (Import / ISO-DIN Mountable)
8 Character / Segment Type LCD Display
Chassis Mounted Rear Auxiliary Inputs
General
•
•
•
•
•
•
•
•
Infrared Remote Control
Media Adapter Cable (2 meter male 3.5mm to male RCA cable)
Programmable Volume Control
Three Preset EQ Curves
Loudness
Rotary Encoder Audio Control
12/24 Hour Clock
Beep Tone Confirmation (On-OFF Option)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
MP6212
INSTALLATION
This unit is designed for installation in cars, trucks and vans with an existing
radio opening. In many cases, a special installation kit will be required to
mount the radio to the dashboard. These kits are available at electronics
supply stores and car stereo specialty shops. Always check the kit
application before purchasing to make sure the kit works with your vehicle.
If you have trouble locating a kit or need installation assistance, contact
Technical Support at 1-800-323-4815 from 8:30am to 7:00pm EST Monday
through Friday and from 9:00am to 5:00pm EST on Saturday.
Preparation
1. Disconnect Battery
Before you begin, always disconnect the battery negative terminal.
NOTE: If the MP6212 is to be installed in a car equipped with an on-
board drive or navigation computer, do not disconnect the battery
cable. If the cable is disconnected, the computer memory may be lost.
Under these conditions, use extra caution during installation to avoid
causing a short circuit.
Tools and Supplies
2. Remove Transport Screws
The following tools and supplies are needed to install the radio:
•
•
•
Torx type, flathead and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver, socket wrench set or other
tools)
TRANSPORT
SCREWS
HALF
SLEEVE
•
•
•
•
•
•
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16-18 gauge speaker wire
MP6212
MOSFET
SF
ET
POWERED
WE
RE
D
/
PTY
CH/CA
T
SCAN
AS
DN
N
UP
P
3. Remove Radio from Sleeve
Lift latches on both sides of sleeve to remove half-sleeve from radio.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
MP6212
Using the Mounting Sleeve
1. Slide the mounting sleeve off the chassis. If it is locked into position,
use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into
it.
BEND TABS
MOUNTING
SLEEVE
RUBBER
CUSHION
MOUNTING BOLT
RADIO
If the opening is too small, carefully cut or file as necessary until the
sleeve easily slides into the opening. Do not force the sleeve into the
opening or cause it to bend or bow. Check for sufficient space behind
the dashboard for the radio chassis.
TRIM RING
Kit Installation
3. Locate the series of bend tabs along the top, bottom, and sides of the
mounting sleeve. With the sleeve fully inserted into the dashboard
opening, bend as many of the tabs outward as necessary to firmly
secure the sleeve to the dashboard.
If your vehicle requires the use of an installation kit to mount this radio,
follow the instructions included with the installation kit to attach the radio to
the mounting plate supplied with the kit.
1. Wire and test the radio as outlined in the Universal Installation instruc-
tions.
2. Install the radio/mounting plate assembly to the sub-dashboard
according to the instructions in the installation kit.
3. Attach the support strap to the radio and dashboard as described in the
Universal Installation instructions.
CAUTION: For proper operation of the CD player, the chassis must be
mounted within 20° of horizontal. Make sure the unit is mounted within
this limitation.
4. Place the radio in front of the dashboard opening so the wiring can be
brought through the mounting sleeve. Follow the wiring diagram
carefully and make certain all connections are secure and insulated
with wire nuts or electrical tape. See “Wiring” on page 5. After
completing the wiring connections, turn the unit on to confirm operation
(vehicle ignition must be on). If the unit does not operate, re-check all
wiring until the problem is corrected.
4. Replace the dashboard trim panel.
5. Make sure the radio is right-side up, then
SPRING CLIP
carefully slide the radio into the mounting
sleeve until it is fully seated and the spring clips
lock it into place.
6. Secure the rear of the unit to the car body
using the mounting bolt and rubber cushion.
7. Test the radio using the Operating Instructions
that follow.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MP6212
ISO Installation
Technical Assistance
This unit has threaded holes in the chassis
side panels which may be used with the
original factory mounting brackets of some
vehicles to mount the radio to the
dashboard. Please consult with your local
car stereo shop for assistance on this type
of installation.
If you require assistance, contact Technical Support at 1-800-323-4815
from 8:30am to 7:00pm EST Monday through Friday and from 9:00am to
5:00pm EST on Saturday.
1. Remove the existing factory radio
from the dashboard or center console
mounting. Save all hardware and
brackets as they will be used to mount the new radio.
2. Carefully unsnap the plastic frame from the front of the new radio
chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing
radio and attach them to the new radio. Do not exceed M5 x 9 MM
maximum screw size. Longer screws may damage components inside
the chassis.
4. Wire the new radio to the vehicle as outlined in the Universal Installation
instructions.
5. Mount the new radio assembly to the dashboard or center console
using the reverse procedure of step 1.
Fuses
When replacing a fuse, make sure the new fuse is the correct type and
amperage. Using an incorrect fuse could damage the radio.
Reconnect Battery
When wiring is complete, reconnect the battery negative terminal.
Removing the Radio
To remove the radio after installation,
remove the trim ring by lifting in the
center and pulling it off from either side.
Insert the removal keys straight back
until they lock, then pull the radio out. If
removal keys are inserted at an angle,
they will not lock properly and will not
release the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
MP6212
WIRING
Satellite Radio In
Antenna
Connect the antenna plug
from the existing antenna
cable (some vehicles
require an adaptor).
Fuse (15 amp fast blow ATO)
Satellite Radio Audio In
Aux-in
R (Red)
R (Red)
Rear Line out
Gray
L (White)
L (White)
Ground
Power Antenna
Connect to power antenna or amplifier.
If not used, tape bare end of wire.
Black
Connect to ground terminal
or clean, unpainted part
of chassis.
Blue
Memory/Battery
Connect to battery or 12 volt
power source that is always live.
The radio will not work if this
wire is not connected.
Yellow
Accessory/Ignition
Connect to existing radio wire
or radio fuse.
Red
FRONT SP
Gray
REAR SP
White/Black
Stripe
White Gray/Black
Stripe
Green/Black
Stripe
Green Purple/Black
Stripe
Purple
Right
Speaker
(Rear)
Left Speaker
(Front)
Right Speaker
(Front)
Left Speaker
(Rear)
NOTE: The amplifier in this radio is only designed for use with four
speakers. Never combine (bridge) outputs for use with two speakers.
Never ground negative speaker leads to chassis ground. Failure to
wire exactly as shown may cause electrical damage to the radio.
NOTE: Only connect speakers with a nominal impedance of 4 ohms.
Speakers with a load impedance less than 4 ohms could damage the
unit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MP6212
FRONT PANEL RELEASE
The front panel release button (4) releases the mechanism that holds the
front panel to the chassis.
Detaching the Front Panel
To detach the front panel, first press the front panel release button to
release the left side of the panel. Next, grasp the released side and pull it off
the chassis. After removing the front panel, store it in the supplied carrying
case to protect it from dirt and damage.
Re-attaching the Front Panel
To re-attach the front panel, make sure the electrical terminals on the back
of the panel are free of dust and dirt, as debris could cause intermittent
operation or other malfunctions. Position the right side of the panel in place
so that it is correctly engaged, then lightly press the left side of the panel
until the mechanism locks it into place.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|